GWO курс по базовой технической подготовке (5 модулей) ПАКЕТ

Целевая аудитория

Этот пакет предназначен для специалистов без опыта работы в мехатронике, электротехнике, гидравлических системах, затяжке болтов с приводом или монтажных работах, а также для тех, кто хочет повысить свои навыки специально для работы в области ветроэнергетики.

Требования к слушателям

Все участники курсов GWO должны создать профиль в системе WINDA для получения WINDA ID, который необходимо предоставить учебному центру до окончания обучения. https://winda.globalwindsafety.org

Все обучающиеся должны быть медицински допущены и иметь возможность полностью участвовать в занятиях.
Перед началом занятий с участников будет взята подпись о медицинской пригодности.

Для получения более подробной информации о требованиях к слушателям свяжитесь с нашим административным отделом.

Содержание модулей

Этот пакет из пяти модулей включает:

1. Общее введение

   • Обзор базовой технической подготовки GWO
   • Принципы безопасности и правильное использование средств индивидуальной защиты
   • Производственные процедуры и требования к командной работе

2. Модуль BTT «Механика»

   • Введение в механику и безопасность
   • Принципы болтовых и сварных соединений
   • Использование ручного инструмента
   • Редуктор, тормозные, поворотные и охлаждающие системы
   • Смазочные системы

3. Модуль BTT «Электротехника»

   • Основы электричества
   • Безопасные электротехнические процедуры
   • Электрические компоненты и датчики
   • Электрические цепи и измерительные приборы

4. Модуль BTT «Гидравлика»

   • Введение в гидравлику и безопасность
   • Насосы, исполнительные механизмы, клапаны и аккумуляторы
   • Датчики, трубопроводы, шланги и соединения
   • Масло, фильтры и гидравлические схемы
   • Инструменты для измерения давления

5. Модуль BTT «Затяжка болтов»

   • Затяжка болтов в ветроэнергетике
   • Затяжка и натяжение болтов с использованием приводного инструмента
   • Применение механических вспомогательных средств

6. Модуль BTT «Монтаж»

   • Монтажные среды и безопасные производственные процедуры
   • Перемещение, хранение и такелажные операции
   • Подготовка основных компонентов, предварительная сборка и сборка
   • Принципы завершения механических, электротехнических и гидравлических работ
   • Работа с кабелями, прокладка, подключение и передача на пусконаладку

7. Финальное оценивание и сертификация

   • Обзор всех модулей
   • Практическое и теоретическое тестирование
   • Регистрация сертификата в базе WINDA

The BTT 6 Modules Package is a combined training programme that includes six GWO Basic Technical Training modules: Mechanical, Electrical, Hydraulic, Bolt Tightening, Installation Mechanical and Installation Electrical.

The BTT 6 Modules Package is a combined training programme designed to provide participants with the essential knowledge and practical skills required to perform basic technical and installation tasks on wind turbines under supervision.

The package covers mechanical, electrical and hydraulic systems, powered bolt tightening, and both mechanical and electrical installation activities. Training follows the Global Wind Organisation (GWO) Basic Technical Training Standard and prepares participants to work safely and effectively under the supervision of an experienced technician, using correct procedures, tools and PPE.

Target Audience

This package is intended for individuals with no previous experience in mechanical, electrical, hydraulic systems, energy-powered bolt tightening or installation activities, as well as those wishing to upskill and apply their knowledge specifically in the wind energy sector.

The package is suitable for personnel preparing to work in wind turbine environments where basic technical knowledge, safe working practices and supervised task performance are required.

Prerequisites

All participants who attend a GWO training course must create a personal profile in WINDA and provide their WINDA ID to the Training Provider before completion of the training.

All personnel participating in this training shall be medically fit and capable of fully participating. Participants’ signatures confirming their medical fitness will be collected before the start of the training.

Before attending the full BTT 6 Modules Package, participants must complete the modules in the required sequence. BTT Bolt Tightening requires prior completion of BTT Mechanical. BTT Installation Mechanical and the combined Installation Mechanical and Installation Electrical delivery require prior completion of BTT Mechanical and BTT Bolt Tightening.

For more details about course prerequisites, please contact our administration desk.

Module Content

This package includes six GWO Basic Technical Training modules:

BTT Mechanical Module

• Mechanical introduction and safety
• Main wind turbine components and mechanical systems
• Principles of bolted and welded connections
• Use of handheld tools
• Gearbox, braking, yaw and cooling systems
• Lubrication systems
• Theoretical test and training review

BTT Electrical Module

• Introduction to electricity
• Electrical safety procedures
• Low and high voltage awareness
• Electrical components and sensors
• Electrical circuits and diagrams
• Electrical measuring instruments
• Theoretical test and training review

BTT Hydraulic Module

• Hydraulic introduction and safety
• Pumps, actuators, valves and accumulators
• Hydraulic sensors, pipes, hoses and connections
• Oil handling, filters and hydraulic diagrams
• Pressure measuring tools
• Theoretical test and training review

BTT Bolt Tightening Module

• Bolt tightening in the wind industry
• Bolt torquing using powered tools
• Bolt tensioning using hydraulic tools
• Planning and preparation of bolt tightening tasks
• Safe and correct use of electrical and hydraulic tools
• Use of mechanical handling aids
• Practical assessment and training review

BTT Installation Mechanical Module

• Introduction to wind turbine installation
• General procedures for working onsite with installation
• Installation environments
• Handling and storing
• Lifting operations
• Main component preparation, pre-assembly and assembly
• Principles of mechanical completion
• Principles of electrical and hydraulic completion
• Operation with external generators
• Theoretical test and training review

BTT Installation Electrical Module

• Introduction to wind turbine installation
• General procedures for working onsite with installation
• Installation environments
• Handling and storing
• Lifting operation hazards
• Main component preparation, pre-assembly and assembly
• Principles of electrical completion
• Principles of hydraulic completion
• Operation with external generators
• Introduction to handover to commissioning
• Theoretical test and training review

Certification

Upon successful completion, participants will receive GWO training records in WINDA for the completed modules:

• BTT Mechanical — BTTM
• BTT Electrical — BTTE
• BTT Hydraulic — BTTH
• BTT Bolt Tightening — BTTB
• BTT Installation Mechanical — BTTI-M
• BTT Installation Electrical — BTTI-E

Duration

7 days

Validity

No expiry period applies. GWO BTT modules are enduring qualifications. Retraining may be required according to company requirements, national legislation, or after an extended period without applying the skills.

Participants

Maximum 12 participants. Practical exercises are delivered according to the applicable GWO instructor-to-participant ratio.

Language

English or another language upon customer request.

FAQ

What certification will I receive after completing the BTT 6 Modules Package?

Upon successful completion, participants will receive GWO WINDA training records for BTT Mechanical, BTT Electrical, BTT Hydraulic, BTT Bolt Tightening, BTT Installation Mechanical and BTT Installation Electrical.

What is the main objective of the BTT 6 Modules Package?

The main objective is to provide participants with basic technical knowledge and practical skills required to perform supervised mechanical, electrical, hydraulic, bolt tightening and installation tasks in the wind industry.

Who should attend this training?

This training is intended for individuals preparing to work in wind turbine environments, including candidates with no previous technical experience and personnel who need basic technical training before progressing to company-specific training.

How long does the training last and what is included?

The BTT 6 Modules Package lasts 7 days and includes Mechanical, Electrical, Hydraulic, Bolt Tightening, Installation Mechanical and Installation Electrical modules.

Why choose Lerus as a training provider?

Lerus delivers GWO-certified training with experienced instructors, practical training facilities and a strong focus on safety, competence and preparation for real wind industry working conditions.